Get Prepared for Your NSE8_812 Exam With Actual 107 Questions
Valid NSE8_812 Test Answers Full-length Practice Certification Exams
NEW QUESTION # 54
Refer to the exhibits.
A customer wants to deploy 12 FortiAP 431F devices on high density conference center, but they do not currently have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy From the FortiSwitch models and sample retail prices shown in the exhibit, which build of materials would have the lowest cost, while fulfilling the customer's requirements?
- A. 2x FortiSwitch 248E-FPOE
- B. 1x FortiSwitch 248EFPOE
- C. 2x FortiSwitch 124E-FPOE
- D. 2x FortiSwitch 224E-POE
Answer: A
Explanation:
The customer wants to deploy 12 FortiAP 431F devices on a high density conference center, but they do not have any PoE switches to connect them to. They want to be able to run them at full power while having network redundancy. PoE switches are switches that can provide both data and power to connected devices over Ethernet cables, eliminating the need for separate power adapters or outlets. PoE switches are useful for deploying devices such as wireless access points, IP cameras, and VoIP phones in locations where power outlets are scarce or inconvenient. The FortiAP 431F is a wireless access point that supports PoE+ (IEEE 802.3at) standard, which can deliver up to 30W of power per port. The FortiAP 431F has a maximum power consumption of 25W when running at full power. Therefore, to run 12 FortiAP 431F devices at full power, the customer needs PoE switches that can provide at least 300W of total PoE power budget (25W x 12). The customer also needs network redundancy, which means that they need at least two PoE switches to connect the FortiAP devices in case one switch fails or loses power. From the FortiSwitch models and sample retail prices shown in the exhibit, the build of materials that has the lowest cost while fulfilling the customer's requirements is 2x FortiSwitch 248E-FPOE. The FortiSwitch 248E-FPOE is a PoE switch that has 48 GE ports with PoE+ capability and a total PoE power budget of 370W. It also has 4x 10 GE SFP+ uplink ports for high-speed connectivity. The sample retail price of the FortiSwitch 248E-FPOE is $1,995, which means that two units will cost $3,990. This is the lowest cost among the other options that can meet the customer's requirements. Option A is incorrect because the FortiSwitch 248EFPOE is a non-PoE switch that has no PoE capability or power budget. It cannot provide power to the FortiAP devices over Ethernet cables. Option B is incorrect because the FortiSwitch 224E-POE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. Option D is incorrect because the FortiSwitch 124E-FPOE is a PoE switch that has only 24 GE ports with PoE+ capability and a total PoE power budget of 185W. It cannot provide enough ports or power to run 12 FortiAP devices at full power. References: https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiSwitch_Secure_Access_Series.pdf https://www.fortinet.com/content/dam/fortinet/assets/data-sheets/FortiAP_400_Series.pdf
NEW QUESTION # 55
Refer to the exhibit showing an SD-WAN configuration.
According to the exhibit, if an internal user pings 10.1.100.2 and 10.1.100.22 from subnet 172.16.205.0/24, which outgoing interfaces will be used?
- A. port16 and port1
- B. port1 and port1
- C. port1 and port15
- D. port16 and port15
Answer: A
Explanation:
According to the exhibit, the SD-WAN configuration has two rules: one for traffic to 10.1.100.0/24 subnet, and one for traffic to 10.1.100.16/28 subnet. The first rule uses the best quality strategy, which selects the SD-WAN member with the best measured quality based on performance SLA metrics. The second rule uses the manual strategy, which specifies port1 as the SD-WAN member to select. Therefore, if an internal user pings 10.1.100.2 and 10.1.100.22 from subnet 172.16.205.0/24, the outgoing interfaces will be port16 and port1 respectively, assuming that port16 has the best quality among the SD-WAN members. Reference: https://docs.fortinet.com/document/fortigate/6.2.14/cookbook/218559/configuring-the-sd-wan-interface
NEW QUESTION # 56
You must analyze an event that happened at 20:37 UTC. One log relevant to the event is extracted from FortiGate logs:
The devices and the administrator are all located in different time zones Daylight savings time (DST) is disabled
* The FortiGate is at GMT-1000.
* The FortiAnalyzer is at GMT-0800
* Your browser local time zone is at GMT-03.00
You want to review this log on FortiAnalyzer GUI, what time should you use as a filter?
- A. 20:37:08
- B. 12.37:08
- C. 17:37:08
- D. 10:37:08
Answer: C
Explanation:
To review this log on FortiAnalyzer GUI, the administrator should use the time filter that matches the local time zone of FortiAnalyzer, which is GMT-0800. Since the log was generated at 20:37 UTC (GMT+0000), the corresponding time in GMT-0800 is 20:37 - 8 hours = 12:37. However, since DST is disabled on FortiAnalyzer, the administrator should add one hour to account for daylight saving time difference, resulting in 12:37 + 1 hour = 13:37. Therefore, the time filter to use is 13:37:08. Reference: https://docs.fortinet.com/document/fortianalyzer/6.4.0/administration-guide/103664/time-zone-and-daylight-saving-time
NEW QUESTION # 57
Refer to the exhibits.
An administrator has configured a FortiGate and Forti Authenticator for two-factor authentication with FortiToken push notifications for their SSL VPN login. Upon initial review of the setup, the administrator has discovered that the customers can manually type in their two-factor code and authenticate but push notifications do not work Based on the information given in the exhibits, what must be done to fix this?
- A. FAC-1 must have an internet routable IP address for push notifications.
- B. On FAC-1, the FortiToken public IP setting must point to 100.64.1 41
- C. On FG-1 CLI, the ftm-push server setting must point to 100.64.141.
- D. On FG-1 port1, the ftm access protocol must be enabled.
Answer: B
Explanation:
https://community.fortinet.com/t5/FortiAuthenticator/Technical-Tip-FortiToken-Push-on-FortiAuthenticator- operation/ta-p/190810
NEW QUESTION # 58
Refer to the exhibit.
To facilitate a large-scale deployment of SD-WAN/ADVPN with FortiGate devices, you are tasked with configuring the FortiGate devices to support injecting of IKE routes on the ADVPN shortcut tunnels.
Which three commands must be added or changed to the FortiGate spoke config vpn ipsec phasei-interface options referenced in the exhibit for the VPN interface to enable this capability? (Choose three.)
- A. set mode-cfg-allow-client-selector enable
- B. set add-route enable
- C. set ike-version 1
- D. set net-device disable
- E. set mode-cfg enable
Answer: A,B,D
Explanation:
A is correct because net-device disable prevents the VPN interface from being added to the routing table as a connected route. This allows IKE routes to be injected instead. D is correct because add-route enable enables IKE route injection on the VPN interface. E is correct because mode-cfg-allow-client-selector enable allows the VPN interface to accept IKE routes from any peer that matches the phase 1 configuration. Reference: https://docs.fortinet.com/document/fortigate/7.0.1/administration-guide/490352/advpn https://docs.fortinet.com/document/fortigate/7.0.1/administration-guide/490352/advpn-configuration
NEW QUESTION # 59
A customer's cybersecurity department needs to implement security for the traffic between two VPCs in AWS, but these belong to different departments within the company. The company uses a single region for all their VPCs.
Which two actions will achieve this requirement while keeping separate management of each department's VPC? (Choose two.)
- A. Create an 1AM account for the cybersecurity department to manage both existing VPC, create a FortiGate HA Cluster on each VPC and IPSEC VPN to force traffic between the VPCs through the FortiGate clusters
- B. Migrate all the instances to the same VPC and create 1AM accounts for each department, then implement a new subnet for a FortiGate auto-scaling group and use routing tables to force the traffic through the FortiGate cluster.
- C. Create a transit VPC with a FortiGate HA cluster, connect to the other two using VPC peering, and use routing tables to force traffic through the FortiGate cluster.
- D. Create a VPC with a FortiGate auto-scaling group with a Transit Gateway attached to the three VPC to force routing through the FortiGate cluster
Answer: C,D
Explanation:
To implement security for the traffic between two VPCs in AWS, while keeping separate management of each department's VPC, two possible actions are:
Create a transit VPC with a FortiGate HA cluster, connect to the other two using VPC peering, and use routing tables to force traffic through the FortiGate cluster. This option allows the cybersecurity department to manage the transit VPC and apply security policies on the FortiGate cluster, while the other departments can manage their own VPCs and instances. The VPC peering connections enable direct communication between the VPCs without using public IPs or gateways. The routing tables can be configured to direct all inter-VPC traffic to the transit VPC.
Create a VPC with a FortiGate auto-scaling group with a Transit Gateway attached to the three VPCs to force routing through the FortiGate cluster. This option also allows the cybersecurity department to manage the security VPC and apply security policies on the FortiGate cluster, while the other departments can manage their own VPCs and instances. The Transit Gateway acts as a network hub that connects multiple VPCs and on-premises networks. The routing tables can be configured to direct all inter-VPC traffic to the security VPC. References: https://docs.fortinet.com/document/fortigate-public-cloud/7.2.0/aws-administration-guide/506140/connecting-a-local-fortigate-to-an-aws-vpc-vpn https://docs.fortinet.com/document/fortigate-public-cloud/7.0.0/sd-wan-architecture-for-enterprise/166334/sd-wan-configuration
NEW QUESTION # 60
Which two methods are supported for importing user defined Lookup Table Data into the FortiSIEM? (Choose two.)
- A. FTP
- B. SCP
- C. API
- D. Report
Answer: A,C
Explanation:
User defined Lookup Table Data (LTD) is a feature that allows users to import custom data into FortiSIEM for correlation, reporting, and analysis purposes. Users can create LTD files in CSV format and import them into FortiSIEM using two methods: FTP or API. FTP is a file transfer protocol that allows users to upload LTD files to a designated folder on the FortiSIEM server. API is an application programming interface that allows users to send HTTP requests to upload LTD files to FortiSIEM using RESTful web services. Reference: https://docs.fortinet.com/document/fortisiem/6.4.0/administration-guide/19662/user-defined-lookup-table-data
NEW QUESTION # 61
Refer to the exhibit.
A customer wants FortiClient EMS configured to deploy to 1500 endpoints. The deployment will be integrated with FortiOS and there is an Active Directory server.
Given the configuration shown in the exhibit, which two statements about the installation are correct? (Choose two.)
- A. You must use Standard or Enterprise SQL Server rather than the included SQL Server Express
- B. If no client update time is specified on EMS, the user will be able to choose the time of installation if they wish to delay.
- C. A client can be eligible for multiple enabled configurations on the EMS server, and one will be chosen based on first priority
- D. You can only deploy initial installations to Windows clients.
- E. The Windows clients only require "File and Printer Sharing0 allowed and the rest is handled by Active Directory group policy
Answer: B,E
Explanation:
A is correct because if no client update time is specified on EMS, the user will be able to choose the time of installation if they wish to delay. This is because the FortiClient EMS server will not force the installation on the client.
E is correct because the Windows clients only require "File and Printer Sharing" allowed and the rest is handled by Active Directory group policy. This is because the Active Directory group policy will configure the Windows clients to automatically install FortiClient and the FortiClient EMS server will only need to push the initial configuration to the clients.
The other options are incorrect. Option B is incorrect because a client can only be eligible for one enabled configuration on the EMS server. Option C is incorrect because you can deploy initial installations to both Windows and macOS clients. Option D is incorrect because you can use the included SQL Server Express to deploy FortiClient EMS.
References:
Deploying FortiClient EMS | FortiClient / FortiOS 7.4.0 - Fortinet Document Library Configuring FortiClient EMS | FortiClient / FortiOS 7.4.0 - Fortinet Document Library FortiClient EMS installation requirements | FortiClient / FortiOS 7.4.0 - Fortinet Document Library
NEW QUESTION # 62
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A customer is trying to set up a VPN with a FortiGate, but they do not have a backup of the configuration. Output during a troubleshooting session is shown in the exhibits A and B and a baseline VPN configuration is shown in Exhibit C Referring to the exhibits, which configuration will restore VPN connectivity?
- A.
- B.
- C.
- D.
Answer: D
Explanation:
The output in Exhibit A shows that the VPN tunnel is not established because the peer IP address is incorrect. The output in Exhibit B shows that the peer IP address is 192.168.1.100, but the baseline VPN configuration in Exhibit C shows that the peer IP address should be 192.168.1.101.
To restore VPN connectivity, you need to change the peer IP address in the VPN tunnel configuration to 192.168.1.101. The correct configuration is shown below:
config vpn ipsec phase1-interface
edit "wan"
set peer-ip 192.168.1.101
set peer-id 192.168.1.101
set dhgrp 1
set auth-mode psk
set psk SECRET_PSK
next
end
Option A is incorrect because it does not change the peer IP address. Option B is incorrect because it changes the peer IP address to 192.168.1.100, which is the incorrect IP address. Option D is incorrect because it does not include the necessary configuration for the VPN tunnel.
NEW QUESTION # 63
You are migrating the branches of a customer to FortiGate devices. They require independent routing tables on the LAN side of the network.
After reviewing the design, you notice the firewall will have many BGP sessions as you have two data centers (DC) and two ISPs per DC while each branch is using at least 10 internal segments.
Based on this scenario, what would you suggest as the more efficient solution, considering that in the future the number of internal segments, DCs or internet links per DC will increase?
- A. Redesign the SD-WAN deployment to only use a single VPN tunnel and segment traffic using VRFs on BGP
- B. No change in design is needed as even small FortiGate devices have a large memory capacity.
- C. Implement network-id, neighbor-group and increase the advertisement-interval
- D. Acquire a FortiGate model with more capacity, considering the next 5 years growth.
Answer: A
Explanation:
Using multiple VPN tunnels and BGP sessions for each internal segment is not scalable and efficient, especially when the number of segments, DCs or internet links per DC increases. A better solution is to use a single VPN tunnel per branch and segment traffic using virtual routing and forwarding (VRF) instances on BGP. This way, each VRF can have its own routing table and BGP session, while sharing the same VPN tunnel. Reference: https://docs.fortinet.com/document/fortigate/6.4.0/cookbook/103439/sd-wan-with-vrf-and-bgp
NEW QUESTION # 64
You are troubleshooting a FortiMail Cloud service integrated with Office 365 where outgoing emails are not reaching the recipients' mail What are two possible reasons for this problem? (Choose two.)
- A. The FortiMail access control rules to relay from Office 365 servers public IPs are missing.
- B. The FortiMail access control rule to relay from Office 365 servers FQDN is missing.
- C. A Mail Flow connector from the Exchange Admin Center has not been set properly to the FortiMail Cloud FQDN.
- D. The FortiMail DKIM key was not set using the Auto Generation option.
Answer: A,B
Explanation:
A: The FortiMail access control rule to relay from Office 365 servers FQDN is missing.
If the access control rule to relay from Office 365 servers FQDN is missing, then FortiMail will not be able to send emails to Office 365. This is because the access control rule specifies which IP addresses or domains are allowed to relay emails through FortiMail.
D: A Mail Flow connector from the Exchange Admin Center has not been set properly to the FortiMail Cloud FQDN.
If the Mail Flow connector from the Exchange Admin Center is not set properly to the FortiMail Cloud FQDN, then Office 365 will not be able to send emails to FortiMail. This is because the Mail Flow connector specifies which SMTP server is used to send emails to external recipients.
NEW QUESTION # 65
Which two statements about bounce address tagging and verification (BATV) on FortiMail are true? (Choose two.)
- A. You must publish the BATV public key as a DNS TXT record.
- B. FortiMail will insert the BATV tag to the sender address in the envelope.
- C. Emails with an empty sender address will be subjected to bounce verification.
- D. BATV will use symmetric keys to verify the bounce address tag.
Answer: B,C
NEW QUESTION # 66
An administrator has configured a FortiGate device to authenticate SSL VPN users using digital certificates.
A FortiAuthenticator is the certificate authority (CA) and the OCSP server.
Part of the FortiGate configuration is shown below:
Based on this configuration, which authentication scenario will FortiGate deny?
- A. FortiAuthenticator responds to an OCSP request that the user certificate authority is untrusted.
- B. The user certificate does not contain the OCSP URL.
- C. FortiAuthenticator responds to an OCSP request that the user certificate status is unknown.
Answer: A
NEW QUESTION # 67
Refer to the CLI output:
Given the information shown in the output, which two statements are correct? (Choose two.)
- A. The IP Reputation feature has been manually updated
- B. Geographical IP policies are enabled and evaluated after local techniques.
- C. An IP address that was previously used by an attacker will always be blocked
- D. Reputation from blacklisted IP addresses from DHCP or PPPoE pools can be restored
- E. Attackers can be blocked before they target the servers behind the FortiWeb.
Answer: D,E
Explanation:
The CLI output shown in the exhibit indicates that FortiWeb has enabled IP Reputation feature with local techniques enabled and geographical IP policies enabled after local techniques (set geoip-policy-order after-local). IP Reputation feature is a feature that allows FortiWeb to block or allow traffic based on the reputation score of IP addresses, which reflects their past malicious activities or behaviors. Local techniques are methods that FortiWeb uses to dynamically update its own blacklist based on its own detection of attacks or violations from IP addresses (such as signature matches, rate limiting, etc.). Geographical IP policies are rules that FortiWeb uses to block or allow traffic based on the geographical location of IP addresses (such as country, region, city, etc.). Therefore, based on the output, one correct statement is that attackers can be blocked before they target the servers behind the FortiWeb. This is because FortiWeb can use IP Reputation feature to block traffic from IP addresses that have a low reputation score or belong to a blacklisted location, which prevents them from reaching the servers and launching attacks. Another correct statement is that reputation from blacklisted IP addresses from DHCP or PPPoE pools can be restored. This is because FortiWeb can use local techniques to remove IP addresses from its own blacklist if they stop sending malicious traffic for a certain period of time (set local-techniques-expire-time), which allows them to regain their reputation and access the servers. This is useful for IP addresses that are dynamically assigned by DHCP or PPPoE and may change frequently. References: https://docs.fortinet.com/document/fortiweb/6.4.0/administration-guide/19662/ip-reputation https://docs.fortinet.com/document/fortiweb/6.4.0/administration-guide/19662/geographical-ip-policies
NEW QUESTION # 68
Refer to the exhibit.
A customer is trying to setup a Playbook automation using a FortiAnalyzer, FortiWeb and FortiGate. The intention is to have the FortiGate quarantine any source of SQL Injection detected by the FortiWeb. They got the automation stitch to trigger on the FortiGate when simulating an attack to their website, but the quarantine object was created with the IP 0.0.0.0. Referring to the configuration and logs in the exhibits, which two statements are true? (Choose two.)
- A. The FortiAnalyzer ADOM Type must be Fabric.
- B. To diagnose this issue, you need to use the commanddiagnose test application oftpd 22.
- C. To fix the issue the parameter for script on the Playbook configuration should be epip.
- D. FortiSOC Playbooks combining FortiWeb and FortiGate are not supported.
- E. The Group By option in the handler should be different to src, so src can be used on the Playbook configuration.
Answer: A,E
NEW QUESTION # 69
You are designing a setup where the FortiGate device is connected to two upstream ISPs using BGP. Part of the requirement is that you must be able to refresh the route advertisements manually without disconnecting the BGP neighborships.
Which feature must you enable on the BGP neighbors to accomplish this goal?
- A. Soft-reconfiguration
- B. Deterministic-med
- C. Synchronization
- D. Graceful-restart
Answer: A
Explanation:
The soft reconfigure is correct by elimination (FGTs all support BGP Refresh, so question is not worded correctly - to refresh routes in advertisements, there is no need to do manually anything, after the change is committed to config FGT will send BGP Refresh message to the peers to notify them of it. The same is true for Cisco and Juniper routers. The question should ask "when routing policy was changed" - then yes, reconfiguraiton is the way to notify BGP peers that BGP policy was changed.
NEW QUESTION # 70
Refer to the exhibit.
A customer wants FortiClient EMS configured to deploy to 1500 endpoints. The deployment will be integrated with FortiOS and there is an Active Directory server.
Given the configuration shown in the exhibit, which two statements about the installation are correct?
(Choose two.)
- A. You can only deploy initial installations to Windows clients.
- B. You must use Standard or Enterprise SQL Server rather than the included SQL Server Express
- C. The Windows clients only require "File and Printer Sharing0 allowed and the rest is handled by Active Directory group policy
- D. A client can be eligible for multiple enabled configurations on the EMS server, and one will be chosen based on first priority
- E. If no client update time is specified on EMS, the user will be able to choose the time of installation if they wish to delay.
Answer: A,D
Explanation:
* A is correct because if no client update time is specified on EMS, the user will be able to choose the time of installation if they wish to delay. This is because the FortiClient EMS server will not force the installation on the client.
* E is correct because the Windows clients only require "File and Printer Sharing" allowed and the rest is handled by Active Directory group policy. This is becausethe Active Directory group policy will configure the Windows clients to automatically install FortiClient and the FortiClient EMS server will only need to push the initial configuration to the clients.
The other options are incorrect. Option B is incorrect because a client can only be eligible for one enabled configuration on the EMS server. Option C is incorrect because you can deploy initial installations to both Windows and macOS clients. Option D is incorrect because you can use the included SQL Server Express to deploy FortiClient EMS.
References:
* Deploying FortiClient EMS | FortiClient / FortiOS 7.4.0 - Fortinet Document Library
* Configuring FortiClient EMS | FortiClient / FortiOS 7.4.0 - Fortinet Document Library
* FortiClient EMS installation requirements | FortiClient / FortiOS 7.4.0 - Fortinet Document Library
https://docs.fortinet.com/document/forticlient/7.0.7/ems-administration-guide/278884/deployment- installershttps://docs.fortinet.com/document/forticlient/7.0.7/ems-administration-guide/374506/deploying- forticlient-software-to-endpoints
NEW QUESTION # 71
Refer to the exhibits.
The exhibits show a FortiGate network topology and the output of the status of high availability on the FortiGate.
Given this information, which statement is correct?
- A. The cluster mode can support a maximum of four (4) FortiGate VMs
- B. The cluster members are on the same network and the IP addresses were statically assigned.
- C. FGVMEVLQOG33WM3D and FGVMEVGCJNHFYI4A share a virtual MAC address.
- D. The ethertype values of the HA packets are 0x8890, 0x8891, and 0x8892
Answer: B
Explanation:
The output of the status of high availability on the FortiGate shows that the cluster mode is active-passive, which means that only one FortiGate unit is active at a time, while the other unit is in standby mode. The active unit handles all traffic and also sends HA heartbeat packets to monitor the standby unit. The standby unit becomes active if it stops receiving heartbeat packets from the active unit, or if it receives a higher priority from another cluster unit. In active-passive mode, all cluster units share a virtual MAC address for each interface, which is used as the source MAC address for all packets forwarded by the cluster. References:
https://docs.fortinet.com/document/fortigate/6.4.0/cookbook/103439/high-availability-with-two-fortigates
NEW QUESTION # 72
A customer is planning on moving their secondary data center to a cloud-based laaS. They want to place all the Oracle-based systems Oracle Cloud, while the other systems will be on Microsoft Azure with ExpressRoute service to their main data center.
They have about 200 branches with two internet services as their only WAN connections. As a security consultant you are asked to design an architecture using Fortinet products with security, redundancy and performance as a priority.
Which two design options are true based on these requirements? (Choose two.)
- A. Two ExpressRoute services to the main data center are required to implement SD-WAN between a FortiGate VM in Azure and a FortiGate device at the data center edge
- B. Branch FortiGate devices must be configured as VPN clients for the branches' internal network to be able to access Oracle services without using public IPs.
- C. Use FortiGate VM for IPSEC over ExpressRoute, as traffic is not encrypted by Azure.
- D. Systems running on Azure will need to go through the main data center to access the services on Oracle Cloud.
Answer: B,D
Explanation:
a) Systems running on Azure will need to go through the main data center to access the services on Oracle Cloud. This is because the Oracle Cloud is not directly connected to the Azure Cloud. The traffic will need to go through the main data center in order to reach the Oracle Cloud.
c) Branch FortiGate devices must be configured as VPN clients for the branches' internal network to be able to access Oracle services without using public IPs. This is because the Oracle Cloud does not allow direct connections from the internet. The traffic will need to go through the FortiGate devices in order to reach the Oracle Cloud.
The other options are not correct.
b) Use FortiGate VM for IPSEC over ExpressRoute, as traffic is not encrypted by Azure. This is not necessary. Azure does encrypt traffic over ExpressRoute.
d) Two ExpressRoute services to the main data center are required to implement SD-WAN between a FortiGate VM in Azure and a FortiGate device at the data center edge. This is not necessary. A single ExpressRoute service can be used to implement SD-WAN between a FortiGate VM in Azure and a FortiGate device at the data center edge.
NEW QUESTION # 73
What is the benefit of using FortiGate NAC LAN Segments?
- A. It allows for assignment of dynamic address objects matching NAC policy.
- B. It provides support for IGMP snooping between hosts within the same VLAN
- C. It provides support for multiple DHCP servers within the same VLAN.
- D. It provides physical isolation without changing the IP address of hosts.
Answer: D
Explanation:
FortiGate NAC LAN Segments are a feature that allows users to assign different VLANs to different LAN segments without changing the IP address of hosts or bouncing the switch port. This provides physical isolation while maintaining firewall sessions and avoiding DHCP issues. One benefit of using FortiGate NAC LAN Segments is that it allows for assignment of dynamic address objects matching NAC policy. This means that users can create firewall policies based on dynamic address objects that match the NAC policy criteria, such as device type, OS type, MAC address, etc. This simplifies firewall policy management and enhances security by applying different security profiles to different types of devices.References:https://docs.fortinet.
com/document/fortigate/7.0.0/new-features/856212/nac-lan-segments-7-0-1
https://docs.fortinet.com/document/fortigate/7.0.0/new-features/856212/nac-lan-segments-7-0-1
NEW QUESTION # 74
......
Accurate & Verified 2025 New NSE8_812 Answers As Experienced in the Actual Test!: https://pass4sure.test4cram.com/NSE8_812_real-exam-dumps.html